Fonts, especially TrueType fonts, use quite a bit of system resources. For optimal performance, trim your fonts down to just those that you need to use on a daily basis and fonts that applications may require.

* Open Control Panel
* Open Fonts folder
* Move fonts you don’t need to a temporary directory (e.g. C:\FONTBKUP?) just in case you need or want to bring a few of them back. The more fonts you uninstall, the more system resources you will gain.

Bookmark It

Hide Sites

You can optimize your pagefile. Setting a fixed size to your pagefile saves the operating system from the need to resize the pagefile.

* Right click on My Computer and select Properties
* Select the Advanced tab
* Under Performance choose the Settings button
* Select the Advanced tab again and under Virtual Memory select Change
* Highlight the drive containing your page file and make the initial Size of the file the same as the Maximum Size of the file.

Windows XP sizes the page file to about 1.5X the amount of actual physical memory by default. While this is good for systems with smaller amounts of memory (under 512MB) it is unlikely that a typical XP desktop system will ever need 1.5 X 512MB or more of virtual memory. If you have less than 512MB of memory, leave the page file at its default size. If you have 512MB or more, change the ratio to 1:1 page file size to physical memory size.

Bookmark It

Hide Sites

1. This is so basic I shouldn’t need to say it, Keep Which Ever E-Mail Program You Use Cleaned Out. I have clients who are always complaining, but who refuse to dump years and years of accumulated e-mail.

2. Make sure you have a good anti virus program (Only one per computer please), have it up to date, and auto monitoring.

3. Make sure you have a good anti spy ware program (Only one per computer), have it up to date, and auto monitoring.

4. Run Disk Clean Up Daily (Start, Programs, Accessories, System Tools, Disk Clean Up - a box opens - make sure each box is checked, click ‘OK’ - a box pops up - Click Yes).

5. Delete Cookies and Cached Files Daily (Start, Control Panel -if you have not done it yet, click ‘Switch To Classic View’, Internet Options - a pop up box will appear - Delete Cookies, Click OK, Click Delete Files - check ‘Delete All Offline Content’ - Click OK, Now Set Your Clear History to no more than 7 Days - if you haven’t used it for a week you probably won’t miss it - Click OK)

6. A very important step almost everyone misses: Empty The Prefetch Folder (Start, My Computer, ‘C’ , Windows, Prefetch Folder, Edit, Select All, File, Delete - pop up box appears - Click Yes, Close Windows Window)

7. Empty Recycle Bin. For the sake of brevity, I am assuming everyone knows where it is and how to empty it.

8. Scan Hard Drive ‘C’ (Start, My Computer, Right Click ‘C’ - box opens - Click Properties at the bottom - another box opens - Click Tools, Click Check Now, Make sure both ‘Automatically fix file system errors’ and ‘Scan for and attempt recovery of bad sectors’ are checked, Click Start. Get a cup of java (oh, black, thank you) and Wait !

9. Defrag Computer (Start, Programs, Accessories, System Tools, Disk Defragmenter - window opens - Select ‘C’ Drive, Click Defragment). Pop a top and Wait !

Bookmark It

Hide Sites

The motherboard is the most expensive computer component so be sure to treat and handle it with great care.There are a few things you should do to ensure no motherboard damage occur as you prepare for the installation.

Be sure you have a clean,well lit,and level work place.Relax your mind and make this task both fun and educational.You will need such tools as a phillips screwdriver,maybe some needle nose pliers and the manual that came with the board.

Most importantly you must remove any and all electrical static discharge from your body and clothes.Static electricity is a big problem and will quickly damage chips on your new board.

PREPARING FOR THE INSTALLATION

Preparing to work on your system envolves work area,lighting, and much more.One great danger is the chance of electrical static charge.But this will be no problem when this static buildup is properly removes.

Remove this danger by grounding yourself.Touch the metal case of the system unit or better yet,touch a door nobt in your work area to remove all electrical static charge.

Set down and carefully read your user’s manual and familiarize yourself with your new motherboard and its layout.Taking this time will boost your motherboard installation performance ike you never thought.

Study your new motherboard and keep the box it came in.Remove it from its protective wrap very carefully and without damaging the wrap.This is done just in case you need to return the motherboard.

You may need to return the motherboard if you made any mistakes in the purchase.Does the holes of your new motherboard line up with the holes in the case?If there are any reason to return the board,you can simply put it back in the box to return.

Make the installation of your new motherboard fun and prepare well.Go to www.ultimatepcrepair.com and click on the photos page to familiarize yourself with all of the components in the cmputer.Follow these procedures as a guildline to install your new motherboard.

REMOVING THE OLD MOTHERBOARD

First Turn on your computer and access your cmos setup. This is done as the computer counts its memory.Press the combination of keys to access your bios.once inside your bios,select "Standard CMOS Setup" and write down all information about your computer’s drives.

Make sure you get the density of your floppy drives and the type of hard drive you have. Once you have this, turn off and unplug the computer and remove the case.

Second Study your system unit layout and you may want to take notes as your remove components and connections so that it will be easier when it comes to re-installing these components or connections.

Go about unplugging the wires that are connected to your old motherboard.Remember to label any and all connections to make re-installing them easier later.Here’s where its very important to take awhile to study your old and new boards before disconnecting anything.

Third Carefully disconnect all drives and label the connectors if needed.Remove the drives and set them out of the way in a safe place.Place all small screws in a cup or something where them won’t get lost.

Carefully grasp the motherboard and give it a gentle tug upwards to be sure on connections,screws,or other devices are not interferring with the board’s removal.

Once you are certain there are no obstruction for the board to be removed,lift the board out of the system unit.Look to see if such components as the memory need to be installed onto the new motherboard.

INSTALLING THE NEW MOTHERBOARD

Installing the new motherboard is the reverse order of removing the old motherboard.Be sure you remove all electrical static discharge from you body and clothes.Inspect the new board for damage and to be certain it is the right motherboard for your computer.

Carefully align the new motherboard with the system unit case and secure the board.Be careful not to secure the screws too much.Install the CPU chip if it is not installed on the board from the manufacturer.

Connect the large power connector from the power supply the the motherboard connector.Take care in not forcing the connector which may bend a pin.

Install RAM Memory into their sockets and check to be sure they are puched in completely.Re-connect all other devices such as controllers,expansion cards and finally the drives.

Check the sound,and videos cards for proper installation. Did you install your internal modem,or scanner adapter card? Connect the leads to the On-Off switch as well the hard drive indicator.

After all connections and components are installed,stop and go back to check again,and then,check some more.Replace the system unit cover once you know all is well.

Your system should now be ready to go.The motherboard may come with a cdrom containing device drivers and other software utilities that may be required to be installed.

Now try turning on the computer and if the POST completed without a hitch,you’re there.If you experience problems,go back and check all connections and devices.

Ita that easy to install or upgrade not only the motherboard,but nearly every other component in the system unit.Get busy understanding your computer now and save big on future PC repair costs.

Bookmark It

Hide Sites

These instruction will assist you in converting the C: partition from FAT32 to NTFS. If you wish to convert another partition instead, just use that drive letter instead of C: while following these instructions.

1. First, back up your data. The conversion process almost always works flawlessly, but there is no point in taking the risk.
2. Click the <Start> button.
3. Click <Run>.
4. Enter "cmd" into the text field labeled "Open".
5. Click the <OK> button.
6. Enter the command "vol c:" to find the volume label for the C: partition.
7. Enter the command "convert c: /fs:ntfs" to convert the C: partition from FAT32 to NTFS.
8. When prompted, enter the volume label for the partition.

Bookmark It

Hide Sites